Fest Flags
Since 2017

The right flag for your boat

What size flag do I need for my boat?
Typical boat flag sizes are 16×24 in or 2×3 ft. Boaters size the flag at the stern at about 1 inch of fly for every foot of boat, rounded up to the next size. A 20 ft boat lands on 16×24 in. Flying a US flag too? Yours usually goes a size or two smaller.

The boater's rule: an inch per foot

America's Boating Club (the U.S. Power Squadrons) sizes the flag at the stern at about one inch of fly for each foot of the boat's overall length. The fly is the long edge, the one that flaps. Nobody sells a 19 inch flag, so you round up to the next size you can buy.

Boat length Flag size
Up to 18 ft 12×18 in
19 to 24 ft 16×24 in
25 to 28 ft 14×28 in
29 to 36 ft 2×3 ft
37 to 60 ft 3×5 ft

Each link opens our boat flag page on that size, double sided. A slimmer 8×18 in is on the page too. This is the size for your main flag at the stern. Flying it next to a US flag? See below.

Flying it next to a US flag?

The same club sizes every other flag on a powerboat a little smaller: about 5/8 inch per foot. On a 30 ft boat that's about 19 inches of fly, so a 16×24 in custom flag next to a 2×3 ft US flag. Where each one goes is in our guide on where to fly a flag on a boat.

How fast do you run?

Once you're on plane, speed matters too. Here's what we've seen hold up:

Flag Speed
16×24 in and smaller Fine at 65+ mph
2×3 ft double sided Up to about 45 mph, with Max stitching
3×5 ft single sided Up to about 45 mph
3×5 ft double sided No-wake speeds, the dock and the sandbar only

Short bursts past 80 mph have held up on 16×24 in and smaller. These are estimates: wind, sun, rain and how the flag is mounted all change how long it lasts.

Single or double sided?

Nearly every boat flag we make is double sided, so it reads right from every side of the water. Single sided is lighter and flies easier; on bigger flags at speed it often lasts longer. More in our single or double-sided guide.

Stitching and grommets

On a moving boat, add stitching. On double-sided boat flags we recommend 6x: our PrecisionLock™ stitching plus tight corner cross stitching. That's extra lines around every edge plus cross-stitched corners, holding the two printed pieces and the liner together where flags wear first. How much room each level needs is in our stitching guide.

Every flag comes with two ClawGrip™ grommets on the left, punched through all three layers on a double-sided flag. The easiest way on is zip ties through the grommets. Rather slide it on? Pick a sleeve when you order.

Trailering to the ramp?

We suggest taking the flag down for the highway ride. The trailer puts hours of steady wind on it for nothing. More ways to keep it flying in our guide to making a flag last.

Corner of a Fest Flags custom flag with a ClawGrip™ grommet and rows of edge stitching
Made to order
Custom boat flag

Your logo, boat name or design. 16×24 in double sided is a typical pick.

  • Sizes from 8×18 in to 3×5 ft, single or double sided
  • 2 ClawGrip™ grommets, extra stitching up to 8x
Build your boat flag

What our customers say

Have a question? Hit us up.

Tell us your boat, how long it is and how fast you run, and we'll help you pick the size.

Keep reading

Sources (read November 14, 2026)
  • America's Boating Club (United States Power Squadrons), Flag and Etiquette Committee flag FAQ: usps.org/national/fecom/faq/flag/flagsize.html
  • America's Boating Club Operations Manual, chapter 12, flag size (August 2024): usps.org/images/secretary/opman/opsman12.pdf
  • Sizes, sides and finishing: our custom boat flag page, festflags.com/products/custom-boat-flags